Hi PhilipIs it possible that for POSIX you use any of the alternative character tables that are hard coded in the pcre2test.c? Ze'ev Atlas
From: Ze'ev Atlas <zatlas1@???>
To: "pcre-dev@???" <pcre-dev@???>
Sent: Wednesday, December 30, 2015 8:41 PM
Subject: Re: [pcre-dev] A question about testinput18
One more clarificationI run tests 1, 2, 11, 14, 15, 16, 18, 20, 21 which I deemed to be relevant to show that the EBCDIC version is well behaving. Most all those tests ran fine (with the expected differences from the ASCII tests) except of test 18. I have yet to fully analyze all the particular details, but only test 18 produces consistently the error messages that we have discussed.
Now test 18 is POSIX and there should be something in the POSIX/EBCDIC combination that causes the test to explode.
My config.h contains this:
#undef PCRE2POSIX_EXP_DEFN
I could not find any other POSIX specific tokens in my configuration.
I compile all the programs with these external options (akin to -D in gcc). Some of those are IBM C related, but the rest are what you would expect when compiling PCRE2 for z/OS. Again, I do not see anything that should adversely affect POSIX
DEF(HAVE_CONFIG_H) DEF(HAVE_STDINT_H) DEF(_XOPEN_SOURCE) DEF(_POSIX_SOURCE) UNDEF(__cplusplus) DEF(PCRE2_CODE_UNIT_WIDTH=8) DEF(NATIVE_ZOS=1) DEF(EBCDIC=1) UNDEF(SUPPORT_JIT) Ze'ev Atlas
From: Ze'ev Atlas <zatlas1@???>
To: "pcre-dev@???" <pcre-dev@???>
Sent: Wednesday, December 30, 2015 8:48 AM
Subject: Re: [pcre-dev] A question about testinput18
Hi PhilI cannot find what is wrong with my email!
I double checked for #define SUPPORT_PCRE2_8 in my config.h and it was there. Then I followed the instructions (see excerpt from the compiler listing below). Then I ran it and sure enough, the output is same as before (see attached)
7260 2139 |while (notdone) 7261 | { 7262 | uint8_t *p; 7263 2140 | int rc = PR_OK; 7264 2141 | BOOL expectdata = TEST(compiled_code, !=, NULL); 7265 |#ifdef SUPPORT_PCRE2_8 7266 2142 | expectdata |= preg.re_pcre2_code != NULL; 7267 2143 |fprintf(outfile, "+++expectdata=%d\n", expectdata); /* <====== Add 7268 |#endif 7269 | 7270 2144 | if (extend_inputline(infile, buffer, expectdata? "data> " : " re7271 2145 | break; 7272 2146 | if (!INTERACTIVE(infile)) fprintf(outfile, "%s", (char *)buffer);7273 2148 | fflush(outfile); 7274 2149 | p = buffer; Ze'ev Atlas
From: "ph10@???" <ph10@???>
To: Ze'ev Atlas <zatlas1@???>
Cc: "pcre-dev@???" <pcre-dev@???>
Sent: Wednesday, December 30, 2015 4:16 AM
Subject: Re: [pcre-dev] A question about testinput18
On Wed, 30 Dec 2015, Ze'ev Atlas wrote:
> It is 0 all the time. Enclosed is the output file (translated to ASCII as usual) Ze'ev Atlas
So it isn't recognising that it has a compiled pattern to test. Did you
check that SUPPORT_PCRE2_8 is defined? Another test would be to move the
added line:
while (notdone)
{
uint8_t *p;
int rc = PR_OK;
BOOL expectdata = TEST(compiled_code, !=, NULL);
#ifdef SUPPORT_PCRE2_8
expectdata |= preg.re_pcre2_code != NULL;
fprintf(outfile, "+++expectdata=%d\n", expectdata); /* <====== Add this line */
#endif
I've moved it inside the #ifdef. If there is no output, then it's not
seeing SUPPORT_PCRE2_8. If there *is* output, something else is going
wrong ... and I will have to think about it.
Philip
--
Philip Hazel
