Revision: 269
http://www.exim.org/viewvc/pcre2?view=rev&revision=269
Author: ph10
Date: 2015-05-17 17:11:40 +0100 (Sun, 17 May 2015)
Log Message:
-----------
Add -fsanitize=undefined test to standard tests.
Modified Paths:
--------------
code/trunk/maint/ManyConfigTests
Modified: code/trunk/maint/ManyConfigTests
===================================================================
--- code/trunk/maint/ManyConfigTests 2015-05-16 16:52:45 UTC (rev 268)
+++ code/trunk/maint/ManyConfigTests 2015-05-17 16:11:40 UTC (rev 269)
@@ -11,6 +11,8 @@
# do this:
#
# -noasan skip the test that uses -fsanitize=address
+# -nousan skip the test that uses -fsanitize=undefined
+# -nodebug skip the test that uses --enable-debug
# -nojit skip JIT tests
# -nomain skip the main set of tests
# -notmp skip the test in a temporary directory
@@ -24,6 +26,8 @@
# much as possible in due course.
useasan=1
+useusan=1
+usedebug=1
usejit=1
usemain=1
usetmp=1
@@ -33,6 +37,8 @@
while [ $# -gt 0 ] ; do
case $1 in
-noasan) useasan=0;;
+ -nousan) useusan=0;;
+ -nodebug) usedebug=0;;
-nojit) usejit=0;;
-nomain) usemain=0;;
-notmp) usetmp=0;;
@@ -137,7 +143,7 @@
pcre2_8=$?
if [ $nlok -gt 0 ]; then
- echo "Running C library tests $withvalgrind"
+ echo "Running PCRE2 library tests $withvalgrind"
$srcdir/RunTest $valgrind >teststdout 2>teststderr
if [ $? -ne 0 -o -s teststderr ]; then
echo " "
@@ -147,7 +153,7 @@
exit 1
fi
else
- echo "Skipping C library tests: newline is $nl"
+ echo "Skipping PCRE2 library tests: newline is $nl"
fi
if [ $nlok -gt 0 -a $pcre2_8 -gt 0 ]; then
@@ -184,10 +190,12 @@
# Update the total count whenever a new test is added; it is used to show
# progess as each test is run.
-testtotal=`expr 21 \* $usemain + \
+testtotal=`expr 20 \* $usemain + \
+ 1 \* $usemain \* $usedebug + \
1 \* $usetmp + \
1 \* $ISGCC \* $usemain + \
1 \* $ISGCC \* $usemain \* $useasan + \
+ 1 \* $ISGCC \* $usemain \* $useusan + \
13 \* $usejit + \
\( 3 + 2 \* $usejit \) \* $usevalgrind`
testcount=0
@@ -210,7 +218,9 @@
# -fsanitize=address, which also may throw up new warnings as well as checking
# things at runtime. Using -fsanitize=address increases the size of stack
# frames by a lot, so run this test with --disable-stack-for-recursion, as
-# otherwise RunTest may fail on test 2.
+# otherwise RunTest may fail on test 2. Finally, run another test using
+# -fsanitize=undefined -std-gnu99 to check for runtime actions that are not
+# well defined.
if [ $usejit -ne 0 ]; then
enable_jit=--enable-jit
@@ -232,6 +242,13 @@
opts="--disable-shared $enable_jit --disable-stack-for-recursion --enable-pcre2-16 --enable-pcre2-32"
runtest
fi
+ if [ $useusan -ne 0 ]; then
+ echo "------- Maximally configured test with -fsanitize=undefined -std=gnu99 -------"
+ CFLAGS="$OFLAGS $SAVECFLAGS -fsanitize=undefined -std=gnu99"
+ echo "CFLAGS=$CFLAGS"
+ opts="--disable-shared $enable_jit --disable-stack-for-recursion --enable-pcre2-16 --enable-pcre2-32"
+ runtest
+ fi
CFLAGS="$OFLAGS $SAVECFLAGS"
fi
@@ -239,9 +256,11 @@
echo "CFLAGS=$CFLAGS"
if [ $usemain -ne 0 ]; then
- echo "---------- Maximally configured test with --enable-debug ----------"
- opts="--disable-shared $enable_jit --enable-pcre2-16 --enable-pcre2-32 --enable-debug"
- runtest
+ if [ $usedebug -ne 0 ]; then
+ echo "---------- Maximally configured test with --enable-debug ----------"
+ opts="--disable-shared $enable_jit --enable-pcre2-16 --enable-pcre2-32 --enable-debug"
+ runtest
+ fi
echo "---------- Non-JIT tests in the current directory ----------"
for opts in \
