Re: [exim-dev] Remembering failed login id

Góra strony
Delete this message
Reply to this message
Autor: Todd Lyons
Data:  
Dla: exim-dev
Temat: Re: [exim-dev] Remembering failed login id
On Thu, Sep 12, 2013 at 10:49 AM, Phil Pennock <pdp@???> wrote:
>> The (very small) patch is attached. It builds without error for me.
>> Look towards the end of this message for session captures illustrating
>> its function.
>
> If I try 2000 AUTH commands in one session, this will only capture the
> last one, right?


In the $authenticated_fail_id variable, yes. It is only indicative of
the last one which failed.

> I think the core code change is probably right, but I'd look at adding a
> failure_log option to the generic authenticator support so that logs can
> be written as each auth attempt fails.


I confirmed that it already does this. I telnet'd to a server and issued:
EHLO tlyons
AUTH PLAIN AG1lMkBleGFtcGxlLmNvbQB3cm9uZw==
RSET
EHLO tlyons
AUTH PLAIN AG1mMkBleGFtcGxlLmNvbQB3cm9uZw==
QUIT

...and this was what was logged, showing that multiple auth id's had been tried:

2013-09-12 18:05:37 plain authenticator failed for tlyons.ivenue.net
(tlyons) [192.168.100.166]: 535 Incorrect authentication data
(set_id=me2@???)
2013-09-12 18:05:55 plain authenticator failed for tlyons.ivenue.net
(tlyons) [192.168.100.166]: 535 Incorrect authentication data
(set_id=mf2@???)

> I'd also check to see if it's safest to string-escape the failed auth id
> immediately, so that it can't contain newlines etc, so it's always safe
> for logging. The protection against this is normally that _valid_ auth
> ids are centrally allocated and trusted to not be malicious. But it


It's already been stringified by existing code. A short while before
the case() where it copies that id into my new global
authenticated_fail_id variable:

    /* The value of authenticated_id is stored in the spool file and printed in
    log lines. It must not contain binary zeros or newline characters. In
    normal use, it never will, but when playing around or testing, this error
    can (did) happen. To guard against this, ensure that the id contains only
    printing characters. */


    if (set_id != NULL) set_id = string_printing(set_id);


Having said that, string_printing() doesn't strip the characters, it
converts them to something safe to print. Trying ^I, ^M and
(randomly) ^O, I saw this:

LOG: quit after auth failed (set_id=me2\n@???)
LOG: quit after auth failed (set_id=me2\r@???)
LOG: quit after auth failed (set_id=me2\017@???)

> might be that the string handling will always handle this safely. Easy


Could be. The log messages generated at auth time for each of the
lines from the QUIT acl above was the same:

LOG: plain authenticator failed for mailc-ef.linkedin.com (tlyons)
[199.101.162.50]: 535 Incorrect authentication data
(set_id=me2\n@???)
LOG: plain authenticator failed for mailc-ef.linkedin.com (tlyons)
[199.101.162.50]: 535 Incorrect authentication data
(set_id=me2\r@???)
LOG: plain authenticator failed for mailc-ef.linkedin.com (tlyons)
[199.101.162.50]: 535 Incorrect authentication data
(set_id=me2\017@???)

> test: send an authid to your patched install which has embedded
> newlines and colons, etc. After all, the only character that can't be
> inside a PLAIN authid is the ASCII NUL.


It does work with the colon too:

LOG: plain authenticator failed for mailc-ef.linkedin.com (tlyons)
[199.101.162.50]: 535 Incorrect authentication data
(set_id=me2:@example.com)
LOG: quit after auth failed (set_id=me2:@example.com)

> Then for the examples, based only on the code you already have, I'd look
> to applying this check into the AUTH ACL too, by the rate-limits. Heck,
> if it were me, I'd have a bounded exponential back-off timer, so that
> each evaluation of AUTH doubles a delay timer, as well as being
> otherwise rate-limited.


It seems better to do this in the ACLs. It wouldn't be too hard to
modify the existing Lena logic for repelling brute force attacks
(shown below) to do that. Maybe make the delay be
20+2^(0$acl_c_authnomail) ...or something like that....assuming that
delay is an expanded option.

Result set: 20, 24, 36, 84, 276
Delay result set: 0, 24, 36, 84, 276

acl_check_auth:
  drop    message        = Authentication is allowed only once per
message in order to slow down bruteforce cracking
          set acl_m_auth = ${eval10:0$acl_m_auth+1}
          condition      = ${if >{$acl_m_auth}{2}}
          delay          = 22s


  drop    message        = Dropped for bruteforce cracking attempt
          set acl_c_authnomail = ${eval10:0$acl_c_authnomail+1}
          condition      = ${if >{$acl_c_authnomail}{4}}
          log_message    = X-Brute-Force: $sender_host_address


...Todd
--
The total budget at all receivers for solving senders' problems is $0.
If you want them to accept your mail and manage it the way you want,
send it the way the spec says to. --John Levine