[exim] Relay access denied (state 14)?

Góra strony
Delete this message
Reply to this message
Autor: Brandon Phelps
Data:  
Dla: exim-users
Temat: [exim] Relay access denied (state 14)?
I've got a primary domain setup and working fine using exim and mysql, people from outside can send email in, and people on the inside can send email out as well as in too. The problem arises when I add another domain to my domains table, and try to send email to that user/domain from outside. If I send the message from the primary domain to the secondary domain, the user gets the message... but when I send it via gmail, etc... I get:

PERM_FAILURE: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 <info@???>: Relay access denied (state 14).

Below is my exim config, anything I'm doing wrong?


# $Cambridge: exim/exim-src/src/configure.default,v 1.13 2007/06/26 11:21:36 ph10 Exp $

######################################################################
#                  Runtime configuration file for Exim               #
######################################################################



# This is a default configuration file which will operate correctly in
# uncomplicated installations. Please see the manual for a complete list
# of all the runtime configuration options that can be included in a
# configuration file. There are many more than are mentioned here. The
# manual is in the file doc/spec.txt in the Exim distribution as a plain
# ASCII file. Other formats (PostScript, Texinfo, HTML, PDF) are available
# from the Exim ftp sites. The manual is also online at the Exim web sites.


# This file is divided into several parts, all but the first of which are
# headed by a line starting with the word "begin". Only those parts that
# are required need to be present. Blank lines, and lines starting with #
# are ignored.


########### IMPORTANT ########## IMPORTANT ########### IMPORTANT ###########
#                                                                          #
# Whenever you change Exim's configuration file, you *must* remember to    #
# HUP the Exim daemon, because it will not pick up the new configuration   #
# until you do. However, any other Exim processes that are started, for    #
# example, a process started by an MUA in order to send a message, will    #
# see the new configuration as soon as it is in place.                     #
#                                                                          #
# You do not need to HUP the daemon for changes in auxiliary files that    #
# are referenced from this file. They are read every time they are used.   #
#                                                                          #
# It is usually a good idea to test a new configuration for syntactic      #
# correctness before installing it (for example, by running the command    #
# "exim -C /config/file.new -bV").                                         #
#                                                                          #
########### IMPORTANT ########## IMPORTANT ########### IMPORTANT ###########




######################################################################
#                    MAIN CONFIGURATION SETTINGS                     #
######################################################################


hide mysql_servers = localhost/maildb/mail/****************

# Specify your host's canonical name here. This should normally be the fully
# qualified "official" name of your host. If this option is not set, the
# uname() function is called to obtain the name. In many cases this does
# the right thing and you need not set anything explicitly.

# primary_hostname =


# The next three settings create two lists of domains and one list of hosts.
# These lists are referred to later in this configuration using the syntax
# +local_domains, +relay_to_domains, and +relay_from_hosts, respectively. They
# are all colon-separated lists:

domainlist local_domains = @:localhost:mysql;SELECT userid FROM domains WHERE userid='$domain'
domainlist relay_to_domains =
hostlist relay_from_hosts = 127.0.0.1

# Most straightforward access control requirements can be obtained by
# appropriate settings of the above options. In more complicated situations,
# you may need to modify the Access Control Lists (ACLs) which appear later in
# this file.

# The first setting specifies your local domains, for example:
#
# domainlist local_domains = my.first.domain : my.second.domain
#
# You can use "@" to mean "the name of the local host", as in the default
# setting above. This is the name that is specified by primary_hostname,
# as specified above (or defaulted). If you do not want to do any local
# deliveries, remove the "@" from the setting above. If you want to accept mail
# addressed to your host's literal IP address, for example, mail addressed to
# "user@???", you can add "@[]" as an item in the local domains
# list. You also need to uncomment "allow_domain_literals" below. This is not
# recommended for today's Internet.

# The second setting specifies domains for which your host is an incoming relay.
# If you are not doing any relaying, you should leave the list empty. However,
# if your host is an MX backup or gateway of some kind for some domains, you
# must set relay_to_domains to match those domains. For example:
#
# domainlist relay_to_domains = *.myco.com : my.friend.org
#
# This will allow any host to relay through your host to those domains.
# See the section of the manual entitled "Control of relaying" for more
# information.

# The third setting specifies hosts that can use your host as an outgoing relay
# to any other host on the Internet. Such a setting commonly refers to a
# complete local network as well as the localhost. For example:
#
# hostlist relay_from_hosts = 127.0.0.1 : 192.168.0.0/16
#
# The "/16" is a bit mask (CIDR notation), not a number of hosts. Note that you
# have to include 127.0.0.1 if you want to allow processes on your host to send
# SMTP mail by using the loopback address. A number of MUAs use this method of
# sending mail.

# All three of these lists may contain many different kinds of item, including
# wildcarded names, regular expressions, and file lookups. See the reference
# manual for details. The lists above are used in the access control lists for
# checking incoming messages. The names of these ACLs are defined here:

acl_smtp_rcpt = acl_check_rcpt
acl_smtp_data = acl_check_data


tls_certificate = /usr/local/exim.cert
tls_privatekey = /usr/local/exim.key

daemon_smtp_ports = 25 : 587
tls_on_connect_ports = 465

qualify_domain = mydomain.com
never_users = root

# The settings below, which are actually the same as the defaults in the
# code, cause Exim to make RFC 1413 (ident) callbacks for all incoming SMTP
# calls. You can limit the hosts to which these calls are made, and/or change
# the timeout that is used. If you set the timeout to zero, all RFC 1413 calls
# are disabled. RFC 1413 calls are cheap and can provide useful information
# for tracing problem messages, but some hosts and firewalls have problems
# with them. This can result in a timeout instead of an immediate refused
# connection, leading to delays on starting up SMTP sessions. (The default was
# reduced from 30s to 5s for release 4.61.)

rfc1413_hosts = *
rfc1413_query_timeout = 5s

# When Exim can neither deliver a message nor return it to sender, it "freezes"
# the delivery error message (aka "bounce message"). There are also other
# circumstances in which messages get frozen. They will stay on the queue for
# ever unless one of the following options is set.

# This option unfreezes frozen bounce messages after two days, tries
# once more to deliver them, and ignores any delivery failures.

ignore_bounce_errors_after = 2d

# This option cancels (removes) frozen messages that are older than a week.

timeout_frozen_after = 7d


######################################################################
#                       ACL CONFIGURATION                            #
#         Specifies access control lists for incoming SMTP mail      #
######################################################################


begin acl

acl_check_rcpt:
  accept  domains       = +local_domains
  accept  hosts = :
  deny    message       = Restricted characters in address
          domains       = +local_domains
          local_parts   = ^[.] : ^.*[@%!/|]
  deny    message       = Restricted characters in address
          domains       = !+local_domains
          local_parts   = ^[./|] : ^.*[@%!] : ^.*/\\.\\./
  accept  local_parts   = postmaster
          domains       = +local_domains
  require verify        = sender
  accept  domains       = +local_domains
  accept  authenticated = *
          control       = submission
  require message = relay not permitted
          domains = +local_domains : +relay_to_domains
  accept


acl_check_data:
accept

######################################################################
#                      ROUTERS CONFIGURATION                         #
#               Specifies how addresses are handled                  #
######################################################################
#     THE ORDER IN WHICH THE ROUTERS ARE DEFINED IS IMPORTANT!       #
# An address is passed to each router in turn until it is accepted.  #
######################################################################


begin routers

dnslookup:
driver = dnslookup
domains = ! +local_domains
transport = remote_smtp
ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
no_more

system_aliases:
driver = redirect
allow_fail
allow_defer
data = ${lookup{$local_part}lsearch{/etc/aliases}}
file_transport = address_file
pipe_transport = address_pipe

localuser:
driver = accept
check_local_user
transport = mysql_delivery
cannot_route_message = Unknown user

mysql_aliases:
    driver = accept
    transport = mysql_delivery


######################################################################
#                      TRANSPORTS CONFIGURATION                      #
######################################################################
#                       ORDER DOES NOT MATTER                        #
#     Only one appropriate transport is called for each delivery.    #
######################################################################


# A transport is used only when referenced from a router that successfully
# handles an address.

begin transports


# This transport is used for delivering messages over SMTP connections.

remote_smtp:
driver = smtp


# This transport is used for local delivery to user mailboxes in traditional
# BSD mailbox format. By default it will be run under the uid and gid of the
# local user, and requires the sticky bit to be set on the /var/mail directory.
# Some systems use the alternative approach of running mail deliveries under a
# particular group instead of using the sticky bit. The commented options below
# show how this can be done.

local_delivery:
driver = appendfile
file = /var/mail/$local_part
delivery_date_add
envelope_to_add
return_path_add
# group = mail
# mode = 0660


# This transport is used for handling pipe deliveries generated by alias or
# .forward files. If the pipe generates any standard output, it is returned
# to the sender of the message as a delivery error. Set return_fail_output
# instead of return_output if you want this to happen only when the pipe fails
# to complete normally. You can set different transports for aliases and
# forwards if you want to - see the references to address_pipe in the routers
# section above.

address_pipe:
driver = pipe
return_output


# This transport is used for handling deliveries directly to files that are
# generated by aliasing or forwarding.

address_file:
driver = appendfile
delivery_date_add
envelope_to_add
return_path_add


# This transport is used for handling autoreplies generated by the filtering
# option of the userforward router.

address_reply:
driver = autoreply

mysql_delivery:
driver = appendfile
directory = ${lookup mysql {SELECT maildir FROM users WHERE username='$local_part@$domain'}}
maildir_format
user = exim
group = mail
mode = 0600
directory_mode = 0770


######################################################################
#                      RETRY CONFIGURATION                           #
######################################################################


begin retry

# This single retry rule applies to all domains and all errors. It specifies
# retries every 15 minutes for 2 hours, then increasing retry intervals,
# starting at 1 hour and increasing each time by a factor of 1.5, up to 16
# hours, then retries every 6 hours until 4 days have passed since the first
# failed delivery.

# WARNING: If you do not have any retry rules at all (this section of the
# configuration is non-existent or empty), Exim will not do any retries of
# messages that fail to get delivered at the first attempt. The effect will
# be to treat temporary errors as permanent. Therefore, DO NOT remove this
# retry rule unless you really don't want any retries.

# Address or Domain    Error       Retries
# -----------------    -----       -------


*                      *           F,2h,15m; G,16h,1h,1.5; F,4d,6h




######################################################################
#                      REWRITE CONFIGURATION                         #
######################################################################


# There are no rewriting specifications in this default configuration file.

begin rewrite


######################################################################
#                   AUTHENTICATION CONFIGURATION                     #
######################################################################


# The following authenticators support plaintext username/password
# authentication using the standard PLAIN mechanism and the traditional
# but non-standard LOGIN mechanism, with Exim acting as the server.
# PLAIN and LOGIN are enough to support most MUA software.
#
# These authenticators are not complete: you need to change the
# server_condition settings to specify how passwords are verified.
# They are set up to offer authentication to the client only if the
# connection is encrypted with TLS, so you also need to add support
# for TLS. See the global configuration options section at the start
# of this file for more about TLS.
#
# The default RCPT ACL checks for successful authentication, and will accept
# messages from authenticated users from anywhere on the Internet.

begin authenticators

# PLAIN authentication has no server prompts. The client sends its
# credentials in one lump, containing an authorization ID (which we do not
# use), an authentication ID, and a password. The latter two appear as
# $auth2 and $auth3 in the configuration and should be checked against a
# valid username and password. In a real configuration you would typically
# use $auth2 as a lookup key, and compare $auth3 against the result of the
# lookup, perhaps using the crypteq{}{} condition.

plain:
  driver                     = plaintext
  public_name                = PLAIN
  server_condition           = "${if crypteq {$3} {${lookup mysql {SELECT crypt FROM users WHERE username='${sg {$2}{'}{}}';}}} {1}{0}}"
  server_set_id              = $2


login:
  driver                     = plaintext
  public_name                = LOGIN
  server_prompts             = "Username:: : Password::"
  server_condition           = "${if crypteq {$2} {${lookup mysql {SELECT crypt FROM users WHERE username='${sg {$1}{'}{}}';}}} {1}{0}}"
  server_set_id              = $1


# LOGIN authentication has traditional prompts and responses. There is no
# authorization ID in this mechanism, so unlike PLAIN the username and
# password are $auth1 and $auth2. Apart from that you can use the same
# server_condition setting for both authenticators.

#LOGIN:
#  driver                     = plaintext
#  server_set_id              = $auth1
#  server_prompts             = <| Username: | Password:
#  server_condition           = Authentication is not yet configured
#  server_advertise_condition = ${if def:tls_cipher }



######################################################################
#                   CONFIGURATION FOR local_scan()                   #
######################################################################


# If you have built Exim to include a local_scan() function that contains
# tables for private options, you can define those options here. Remember to
# uncomment the "begin" line. It is commented by default because it provokes
# an error with Exim binaries that are not built with LOCAL_SCAN_HAS_OPTIONS
# set in the Local/Makefile.

# begin local_scan


# End of Exim configuration file
begin:vcard
fn:Brandon Phelps
n:Phelps;Brandon
org:Dell Sports;Development
adr:;;;Charlotte;NC;28207;USA
email;internet:brandon@???
title:Network Administrator
tel;home:(704) 222-2103
tel;cell:(704) 222-2103
x-mozilla-html:FALSE
url:http://www.dellsports.com
version:2.1
end:vcard