On Friday 01 September 2006 13:51, Stephen Gran wrote:
> On Fri, Sep 01, 2006 at 01:40:49PM +0200, Oliver König said:
> > When a subscriber posts to the list /var/log/exim4/mainlog says:
> > 2006-09-01 13:37:27 H=mailout09.sul.t-online.com [194.25.134.84]
> > F=<k.oliver@???> rejected RCPT <news@???>:
> > relay not permitted
> >
> > Any idea how to allow postings from subscribers? Thanks.
>
> It sounds to me like you don't have +MAILMAN_DOMAINS in any accept
> statements in your rcpt acl. I would just add it to one of the verify =
> recipient stanzas towards the end of the rcpt acl (given a stock
> configuration).
Hello Stephen,
thanks for for reply. I added +MAILMAN_DOMAINS whereever I thought it might
help. I am still getting the same error: relay not permitted. Here are
excerpts from my exim config:
[..]
.ifndef MAIN_LOCAL_DOMAINS
MAIN_LOCAL_DOMAINS = DEBCONFlocal_domainsDEBCONF
.endif
domainlist local_domains = MAIN_LOCAL_DOMAINS : MAILMAN_DOMAINS :
server.windfinder.com
.ifndef MAIN_RELAY_TO_DOMAINS
MAIN_RELAY_TO_DOMAINS = DEBCONFrelay_domainsDEBCONF
.endif
domainlist relay_to_domains = MAIN_RELAY_TO_DOMAINS
.ifndef MAIN_RELAY_NETS
MAIN_RELAY_NETS = DEBCONFrelay_netsDEBCONF
.endif
hostlist relay_from_hosts = 127.0.0.1 : ::::1 : MAIN_RELAY_NETS
[..]
# Home dir for your Mailman installation -- aka Mailman's prefix
# directory, see: /usr/share/doc/mailman/README.exim.
MAILMAN_HOME=/var/lib/mailman
MAILMAN_WRAP=MAILMAN_HOME/mail/mailman
# User and group for Mailman, should match your --with-mail-gid
# switch to Mailman's configure script.
MAILMAN_USER=list
MAILMAN_GROUP=daemon
# Domains that your lists are in - colon separated list
# you may wish to add these into local_domains as well
domainlist MAILMAN_DOMAINS= server.windfinder.com
#
# -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=
#
# These values are derived from the ones above and should not need
# editing unless you have munged your mailman installation
#
# The path of the list config file (used as a required file when
# verifying list addresses)
MAILMAN_LISTCHK=MAILMAN_HOME/lists/${lc::$local_part}/config.pck
[..]
begin routers
mailman_router:
driver = accept
require_files = MAILMAN_HOME/lists/$local_part/config.pck
local_part_suffix_optional
local_part_suffix = -bounces : -bounces+* : \
-confirm+* : -join : -leave : \
-owner : -request : -admin
domains = server.windfinder.com : MAILMAN_DOMAINS
transport = mailman_transport
[..]
# Accept if the address is in a local domain, but only if the recipient can
# be verified. Otherwise deny. The "endpass" line is the border between
# passing on to the next ACL statement (if tests above it fail) or denying
# access (if tests below it fail).
#
accept
domains = +local_domains : +MAILMAN_DOMAINS
endpass
message = unknown user
verify = recipient
# Accept if the address is in a domain for which we are relaying, but again,
# only if the recipient can be verified.
#
# If you want to use the more conservative "unknown user" error
# message in case of a non-existing local part, you might want to
# set CHECK_RCPT_GIVE_UNKNOWN_USER. However, this might reveal
# local information, which is the cause for it not being enabled by
# default.
accept
domains = +relay_to_domains : +MAILMAN_DOMAINS
endpass
.ifdef CHECK_RCPT_GIVE_UNKNOWN_USER
message = ${if eq{$acl_verify_message}{Unrouteable address}{unknown user}
{$acl_verify_message}}
.else
message = unrouteable address
.endif
verify = recipient
[..]
begin transports
mailman_transport:
driver = pipe
command = MAILMAN_WRAP \
'${if def:local_part_suffix \
{${sg{$local_part_suffix}{-(\\w+)(\\+.*)?}{\$1}}} \
{post}}' \
$local_part
current_directory = MAILMAN_HOME
home_directory = MAILMAN_HOME
user = MAILMAN_USER
group = MAILMAN_GROUP
Regards,
Oliver
