Re: [exim] SMTP AUTH help

Pàgina inicial
Delete this message
Reply to this message
Autor: joe
Data:  
A: Tony Finch
CC: exim-users
Assumpte: Re: [exim] SMTP AUTH help
Ok, I tried changing the settings. I changed:

relay_to_domains =
acl_whitelist_local_deny:
  accept hosts = ${if exists{CONFDIR/local_host_whitelist}\
                        {CONFDIR/local_host_whitelist}\
                        {}}
  accept senders = ${if exists{CONFDIR/local_sender_whitelist}\
                        {CONFDIR/local_sender_whitelist}\
                        {}}


acl_check_rcpt:
accept hosts = :

  deny    domains       = +local_domains
          local_parts   = ^[.] : ^.*[@%!/|]
          message       = restricted characters in address


  deny    domains       = !+local_domains
          local_parts   = ^[./|] : ^.*[@%!] : ^.*/\\.\\./
          message       = restricted characters in address


  accept local_parts = postmaster
         domains = +local_domains


  deny message = sender envelope address $sender_address is locally
blacklisted here. If you think this is wrong, get in touch with postmaster
       !acl = acl_whitelist_local_deny
       senders = ${if exists{CONFDIR/local_sender_blacklist}\
                             {CONFDIR/local_sender_blacklist}\
                             {}}


  deny message = sender IP address $sender_host_address is locally
blacklisted here. If you think this is wrong, get in touch with postmaster
       !acl = acl_whitelist_local_deny
       hosts = ${if exists{CONFDIR/local_host_blacklist}\
                             {CONFDIR/local_host_blacklist}\
                             {}}


  accept domains = +local_domains
         endpass
         message = unknown user
         verify = recipient


  accept domains = +relay_to_domains
         endpass
         message = unrouteable address
         verify = recipient


accept hosts = +relay_from_hosts

accept authenticated = *

deny message = relay not permitted

acl_check_data:
   warn condition = ${if !def:h_Message-ID: {1}}
        hosts = +relay_from_hosts
        message = Message-ID: <E$message_id@$primary_hostname>



accept

login:
driver = plaintext
public_name = PLAIN
server_prompts = Username:: : Password::
server_condition = ${if and {{eq{$2}{user}}{eq{$3}{pass}}}{yes}{no}}
server_set_id = $2

For some reason with these settings, I cannot authenticate. Apparently I was
wrong when I said authentication was working because when I tried it, it
just kept prompting me over and over. So, I changed authenticators to this,
which in theory should allow a connection with login of user, and password
of pass. Pretty simple, but, it does the same thing. Any ideas?


----- Original Message -----
From: "Tony Finch" <dot@???>
To: "Joe Csernik" <joe@???>
Cc: <exim-users@???>
Sent: Sunday, February 06, 2005 1:54 PM
Subject: Re: [exim] SMTP AUTH help


> On Sat, 5 Feb 2005, Joe Csernik wrote:
>
> > I REALLY need to deny access to SMTP from users that are not

authenticated.
>
> Your relay_from_hosts list only contains localhost, so your ACL below
> says that your users must be authenticated if they want to send email to
> non-local domains, but don't have to be if they send to local domains.
> Unless you separate your MX from your outgoing relay (which is a very good
> idea, because it makes life harder for spammers) this is the best you can
> do.
>
> >   accept domains = +local_domains
> >          endpass
> >          message = unknown user
> >          verify = recipient

> >
> >   accept domains = +relay_to_domains
> >          endpass
> >          message = unrouteable address
> >          verify = recipient

> >
> > accept hosts = +relay_from_hosts
> >
> > accept authenticated = *
>
> Tony.
> --
> <fanf@???> <dot@???> http://dotat.at/ ${sg{\N${sg{\
> N\}{([^N]*)(.)(.)(.*)}{\$1\$3\$2\$1\$3\n\$2\$3\$4\$3\n\$3\$2\$4}}\
> \N}{([^N]*)(.)(.)(.*)}{\$1\$3\$2\$1\$3\n\$2\$3\$4\$3\n\$3\$2\$4}}
>
> --
> ## List details at http://www.exim.org/mailman/listinfo/exim-users Exim

details at http://www.exim.org/ ##
>