Re: [exim] exim cygwin and dsearch (kind of long)

トップ ページ
このメッセージを削除
このメッセージに返信
著者: mnsanghvi
日付:  
To: Peter Bowyer, exim-users
CC: 
題目: Re: [exim] exim cygwin and dsearch (kind of long)
'allo,


    I got rid of the relay_to_domains setting and it is empty now as it was.
    But now I keep getting the following error: 


2004-08-25 03:49:27 H=sccrmhc11.comcast.net [204.127.202.55] F=<mnsanghvi@???> rejected RCPT <mns-usenet@???>: relay not permitted

"relay not permitted" seems to be like something coming out of the ACL section
and sure enough there is an ACL in there which uses relay_to_domains to
decide if it wants to accept the email or not.

  accept  domains       = +relay_to_domains
              endpass
              verify        = recipient


So I changed the "relay_to_domains" to "virtual_domains" but all that did
was prevent any email coming in. I saw nothing in the log files. 'tail -f' just
stayed empty. I switched back to having "relay_to_domains" and
now email is flowing again, though it is being rejected due to passing
through all the ACLs until it reaches the last ACL. Here are the ACLs
that came as default settings under Cygwin:


begin acl

acl_check_rcpt:

       accept  hosts = :


       deny    message       = Restricted characters in address
                  domains       = +local_domains
                  local_parts   = ^[.] : ^.*[@%!/|]


       deny    message       = Restricted characters in address
                  domains       = !+local_domains
                  local_parts   = ^[./|] : ^.*[@%!] : ^.*/\\.\\./



        accept  local_parts   = postmaster
                    domains       = +local_domains


        require verify        = sender


       accept  domains       = +local_domains
                   endpass
                   verify        = recipient


        accept  domains       = +relay_to_domains
                    endpass
                    verify        = recipient


         accept  hosts         = +relay_from_hosts


         accept  authenticated = *


          deny    message       = relay not permitted



Everything else seems to be defaulted, so I can't think of anything else that
could be causing the "relay not permitted" to show up.

I am assuming that I probably need some ACL added to the default set, but
am not sure what it should be.


cheers,

        mehul



> mnsanghvi@??? said:
> > OK. So I've got things setup in my /etc/exim.conf with a few diffrences
> > from the default setup that ships with Cygwin. I have attached the output
> > of the diff with this email.
> >
> > Using that configuration, below are the kinds of error messages that
> > I am seeing (I've changed the actual domain to hide it, but the message
> > is cut and pasted as is):
> >
> > 2004-08-25 02:25:42 lowest numbered MX record points to local host: t.com
> > (while verifying <mns-usenet@???> from host sccrmhc13.comcast.net
> > [204.127.202.64])
> > 2004-08-25 02:25:42 H=sccrmhc13.comcast.net [204.127.202.64]
> > F=<mnsanghvi@???> temporarily rejected RCPT <mns-usenet@???>:
> > lowest numbered MX record points to local host
>
> You shouldn't list the virtual domains in your relay_to_domains domainlist
> - that causes them to be treated as remote, but when Exim looks in the DNS
> for somewhere to send them, the MX is iteself - hence it's confused.
>
> Peter
>
> --
>
> ## List details at http://www.exim.org/mailman/listinfo/exim-users Exim details
> at http://www.exim.org/ ##