Re: [Exim] Exim Help

Kezdőlap
Üzenet törlése
Válasz az üzenetre
Szerző: William Thompson
Dátum:  
Címzett: Bhavesh Shah
CC: exim-users
Tárgy: Re: [Exim] Exim Help
> Sorry to trouble you again and again but I am not that familiar with Exim. When I added
> bad_recipients:
>     driver = smartuser
>     new_address = ${lookup{$local_part@$domain}lsearch{etc/exim/bad_recipients}{nouser}fail}
>     verify_only
>     fail_verify_recipient

>
> I got the following error:
>
> 2003-04-11 11:20:00 Exim configuration error
> router bad_recipients: cannot find router driver "smartuser" in line 365
> 2003-04-11 11:20:00 Exim configuration error
> option "new_address" unknown in line 366 ("driver" must be specified before any private options)
> 2003-04-11 11:20:00 Exim configuration error
> router bad_recipients: cannot find router driver "smartuser" in line 367
> 2003-04-11 11:20:00 Exim configuration error
> router bad_recipients: cannot find router driver "smartuser" in line 368
> Segmentation Fault


You need to put it in the directors section, not routers.

> -----Original Message-----
> From: William Thompson [mailto:wt@electro-mechanical.com]
> Sent: Friday, April 11, 2003 10:44 AM
> To: Bhavesh Shah
> Cc: exim-users@???
> Subject: Re: [Exim] Exim Help
>
> > I am using Exim 3.22 does it support ACL? As configuration file doesn't have section related to ACL or can I add it as a separate section?
> > Also if I use ACL as you rightly suggested then should I have to use below router along with ACL you specified?
> > verify_check_specials:
> >             driver = domainlist
> >             condition = "${if eq local_part@$domain}{X@???}{yes}{no}}"
> >             verify_only
> >             fail_verify
> >             route_list = *

>
> No, ACLs first appeared in exim v4.
>
> You'd have to do this if you want it to work in exim 3.x:
> Under your directors configuration put:
> bad_recipients:
>     driver = smartuser
>     new_address = ${lookup{$local_part@$domain}lsearch{etc/exim/bad_recipients}{nouser}fail}
>     verify_only
>     fail_verify_recipient

>
> If you want it to fail both sender and recipient, change
> fail_verify_recipient to fail_verify
>
> I can't guarentee that it will work. Another solution would be to use an
> alias file (or one that has both localparts and domains) and use the :fail:
> syntax.
>
> > -----Original Message-----
> > From: William Thompson [mailto:wt@electro-mechanical.com]
> > Sent: Friday, April 11, 2003 10:24 AM
> > To: Bhavesh Shah
> > Cc: exim-users@???
> > Subject: Re: [Exim] Exim Help
> >
> > > Hi John,
> > > Yes single email works fine.
> > > Here is the router configuration
> > >
> > > verify_check_specials:
> > >            driver = domainlist
> > >            condition = "${if eq local_part@$domain}{X@???}{yes}{no}}"
> > >            verify_only
> > >            fail_verify
> > >            route_list = *

> > >
> > > but for multiple recipient to block can you suggest what should my ACL or router should look like?
> > > Thanks and appreciate it.
> >
> > I used to use a router (er director on 3.35) to do this and upon upgrading,
> > I went to the acl.  Here's my ACL (It's almost to the top of the acl)
> > deny    message = ${if !eq{$address_data}{}\
> >             {$address_data}\
> >             {$local_part@$domain is not a valid mailbox}\
> >            }
> >     log_message = Listed in bad_recipients
> >     domains = +local_domains
> >     recipients = lsearch*;/etc/exim4/bad_recipients

> >
> > the domains is only there to keep me from goofing some things up and so the
> > acl doesn't check every rcpt to.