----- Original Message -----
From: "Davide Minardi" <davide@???>
To: "Exim Mailing List" <exim-users@???>
Sent: Wednesday, August 30, 2006 10:31 AM
Subject: Re: [exim] R: Exim4 And outgoing Filters
>
>
> This is router section of conf file
>
>
> ### router/200_exim4-config_primary
> #################################
> # This file holds the primary router, responsible for nonlocal mails
>
> .ifdef DCconfig_internet
> # configtype=internet
> #
> # deliver mail to the recipient if recipient domain is a domain we
> # relay for. We do not ignore any target hosts here since delivering to
> # a site local or even a link local address might be wanted here, and if
> # such an address has found its way into the MX record of such a domain,
> # the local admin is probably in a place where that broken MX record
> # could be fixed.
>
> dnslookup_relay_to_domains:
> debug_print = "R: dnslookup_relay_to_domains for $local_part@$domain"
> driver = dnslookup
> domains = ! +local_domains : +relay_to_domains
> transport = remote_smtp
> same_domain_copy_routing = yes
> no_more
>
> # deliver mail directly to the recipient. This router is only reached
> # for domains that we do not relay for. Since we most probably can't
> # have broken MX records pointing to site local or link local IP
> # addresses fixed, we ignore target hosts pointing to these addresses.
>
> dnslookup:
> debug_print = "R: dnslookup for $local_part@$domain"
> driver = dnslookup
> domains = ! +local_domains
> transport = remote_smtp
> same_domain_copy_routing = yes
> # ignore private rfc1918 and APIPA addresses
> ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\
> 172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16
> no_more
>
> .endif
>
>
> .ifdef DCconfig_local
> # configtype=local
> #
> # Stand-alone system, so generate an error for mail to a non-local domain
> nonlocal:
> debug_print = "R: nonlocal for $local_part@$domain"
> driver = redirect
> domains = ! +local_domains
> allow_fail
> data = :fail: Mailing to remote domains not supported
> no_more
>
> .endif
>
>
> .ifdef DCconfig_smarthost DCconfig_satellite
> # configtype=smarthost or configtype=satellite
> #
> # Send all non-local mail to a single other machine (smarthost).
> #
> # This means _ALL_ non-local mail goes to the smarthost. This will most
> # probably not do what you want for domains that are listed in
> # relay_domains. The most typical use for relay_domains is to control
> # relaying for incoming e-mail on secondary MX hosts. In that case,
> # it doesn't make sense to send the mail to the smarthost since the
> # smarthost will probably send the message right back here, causing a
> # loop.
> #
> # If you want to use a smarthost while being secondary MX for some
> # domains, you'll need to copy the dnslookup_relay_to_domains router
> # here so that mail to relay_domains is handled separately.
>
> smarthost:
> debug_print = "R: smarthost for $local_part@$domain"
> driver = manualroute
> domains = ! +local_domains
> transport = remote_smtp_smarthost
> route_list = * DCsmarthost byname
> host_find_failed = defer
> same_domain_copy_routing = yes
> no_more
>
> .endif
>
>
> dnslookup:
> driver = dnslookup
> domains = ! +local_domains
> transport = remote_smtp
> ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
>
> sentarchiver:
> driver = dnslookup
> domains = ! +local_domains
> transport = sent_archive_delivery
> ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
>
> sent_archive_delivery:
> driver = appendfile
> user = raziel
> group = raziel
> delivery_date_add
> envelope_to_add
> return_path_add
> maildir_format=true
> mode = 0770
> directory = /home/raziel/Maildir/.Sent
> create_directory = true
> directory_mode = 0770
> no_mode_fail_narrower
>
>
>
>
> # The "no_more" above means that all later routers are for
> # domains in the local_domains list, i.e. just like Exim 3 directors.
> #####################################################
> ### end router/200_exim4-config_primary
> #####################################################
> ----- Original Message -----
> From: "W B Hacker" <wbh@???>
> To: "exim users" <exim-users@???>
> Sent: Wednesday, August 30, 2006 10:17 AM
> Subject: Re: [exim] R: Exim4 And outgoing Filters
>
>
>> Davide Minardi wrote:
>>
>>> ok the problem is in the last chunk of code ... sent_archive_delivery...
>>> +
>>> Error message :
>>> router sent_archive_delivery : cannot find rouiter driver " appendfile "
>>> ..invalid new config file ----- bla bla bla
>>>
>>> ;????
>>
>> Cut and paste that whole section - unaltered. No need to obfuscate -
>> there
>> is
>> noting all that sensitive in the router/transport section.
>>
>> I suspect you have a faulted line-break, missing colon, or extraneous
>> '#'.
>>
>> Do also, from the CLI:
>>
>> exim -bV
>>
>> (uppercase'V' there)
>>
>> And paste that too.
>>
>> Waitin'
>>
>> Bill
>>
>>
>> --
>> ## List details at http://www.exim.org/mailman/listinfo/exim-users
>> ## Exim details at http://www.exim.org/
>> ## Please use the Wiki with this list - http://www.exim.org/eximwiki/
>>
>
>
> --
> ## List details at http://www.exim.org/mailman/listinfo/exim-users
> ## Exim details at http://www.exim.org/
> ## Please use the Wiki with this list - http://www.exim.org/eximwiki/
>
