This is router section of conf file
### router/200_exim4-config_primary
#################################
# This file holds the primary router, responsible for nonlocal mails
.ifdef DCconfig_internet
# configtype=internet
#
# deliver mail to the recipient if recipient domain is a domain we
# relay for. We do not ignore any target hosts here since delivering to
# a site local or even a link local address might be wanted here, and if
# such an address has found its way into the MX record of such a domain,
# the local admin is probably in a place where that broken MX record
# could be fixed.
dnslookup_relay_to_domains:
debug_print = "R: dnslookup_relay_to_domains for $local_part@$domain"
driver = dnslookup
domains = ! +local_domains : +relay_to_domains
transport = remote_smtp
same_domain_copy_routing = yes
no_more
# deliver mail directly to the recipient. This router is only reached
# for domains that we do not relay for. Since we most probably can't
# have broken MX records pointing to site local or link local IP
# addresses fixed, we ignore target hosts pointing to these addresses.
dnslookup:
debug_print = "R: dnslookup for $local_part@$domain"
driver = dnslookup
domains = ! +local_domains
transport = remote_smtp
same_domain_copy_routing = yes
# ignore private rfc1918 and APIPA addresses
ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\
172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16
no_more
.endif
.ifdef DCconfig_local
# configtype=local
#
# Stand-alone system, so generate an error for mail to a non-local domain
nonlocal:
debug_print = "R: nonlocal for $local_part@$domain"
driver = redirect
domains = ! +local_domains
allow_fail
data = :fail: Mailing to remote domains not supported
no_more
.endif
.ifdef DCconfig_smarthost DCconfig_satellite
# configtype=smarthost or configtype=satellite
#
# Send all non-local mail to a single other machine (smarthost).
#
# This means _ALL_ non-local mail goes to the smarthost. This will most
# probably not do what you want for domains that are listed in
# relay_domains. The most typical use for relay_domains is to control
# relaying for incoming e-mail on secondary MX hosts. In that case,
# it doesn't make sense to send the mail to the smarthost since the
# smarthost will probably send the message right back here, causing a
# loop.
#
# If you want to use a smarthost while being secondary MX for some
# domains, you'll need to copy the dnslookup_relay_to_domains router
# here so that mail to relay_domains is handled separately.
smarthost:
debug_print = "R: smarthost for $local_part@$domain"
driver = manualroute
domains = ! +local_domains
transport = remote_smtp_smarthost
route_list = * DCsmarthost byname
host_find_failed = defer
same_domain_copy_routing = yes
no_more
.endif
dnslookup:
driver = dnslookup
domains = ! +local_domains
transport = remote_smtp
ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
sentarchiver:
driver = dnslookup
domains = ! +local_domains
transport = sent_archive_delivery
ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
sent_archive_delivery:
driver = appendfile
user = raziel
group = raziel
delivery_date_add
envelope_to_add
return_path_add
maildir_format=true
mode = 0770
directory = /home/raziel/Maildir/.Sent
create_directory = true
directory_mode = 0770
no_mode_fail_narrower
# The "no_more" above means that all later routers are for
# domains in the local_domains list, i.e. just like Exim 3 directors.
#####################################################
### end router/200_exim4-config_primary
#####################################################
----- Original Message -----
From: "W B Hacker" <wbh@???>
To: "exim users" <exim-users@???>
Sent: Wednesday, August 30, 2006 10:17 AM
Subject: Re: [exim] R: Exim4 And outgoing Filters
> Davide Minardi wrote:
>
>> ok the problem is in the last chunk of code ... sent_archive_delivery...
>> +
>> Error message :
>> router sent_archive_delivery : cannot find rouiter driver " appendfile "
>> ..invalid new config file ----- bla bla bla
>>
>> ;????
>
> Cut and paste that whole section - unaltered. No need to obfuscate - there
> is
> noting all that sensitive in the router/transport section.
>
> I suspect you have a faulted line-break, missing colon, or extraneous '#'.
>
> Do also, from the CLI:
>
> exim -bV
>
> (uppercase'V' there)
>
> And paste that too.
>
> Waitin'
>
> Bill
>
>
> --
> ## List details at http://www.exim.org/mailman/listinfo/exim-users
> ## Exim details at http://www.exim.org/
> ## Please use the Wiki with this list - http://www.exim.org/eximwiki/
>
